An HVAC quote (US) or estimate, and a UK quotation, only holds if the scope is on the page: old unit, new unit, line set, electrical, crane, permit, what is out. Write the number before you start the changeout. Helmate is an app for the job that number belongs to — it does not build the quote for you. Basic: first month free, then $25/month for one open project.
The homeowner says 'just swap the condenser'. On the pad you find a 1998 coil, mismatched SEER, a disconnected condensate that has been draining into the wall, and a breaker that will not take the new MCA. If your HVAC quote was one line — 'changeout $X' — you are now doing extra work with no paper. In Canada many shops still say estimate for the same document. In the UK a heating engineer sends a quotation. Use the word the customer will look for. Put the scope in every language the same way: what is in, what is out, and the price.
Helmate does not print the quote. There is no Helmate 'estimate builder'. The honest product is the project: the PDF you already sent, the notes from the attic, the receipts from the branch, the photos before you pull the old unit. Keep them on the job. If you need a field-service quoter, that is a different product — see the Jobber alternative page for an honest split, without invented prices.
Quote, estimate, quotation — same job, different English
US HVAC customers Google 'quote'. Many techs still write 'estimate' on the door hanger. UK customers ask for a quotation from a heating engineer. Australian air-con tradies quote the install. Canadian HVAC shops mix estimate and quote. On Helmate country pages the jargon follows the market: US, UK, Australia, Canada. The document must still list the equipment, the labour, the exclusions, and the date it is good until.
Do not hide crane, recovery, permit, or electrical in 'misc'. If you do not know the crane yet, write 'crane extra, quoted when the site is measured'. A low number that explodes on day two is not competitive. It is a future argument.
What must be on a changeout number
- Old unit: make, model, refrigerant, and that recovery is included or not
- New unit: make, model, tonnage, SEER/HSPF or the local equivalent
- Line set, whip, pad or curb, condensate, electrical, thermostat
- Crane, roof access, permit, disposal — in or out
- What happens if the coil in the attic does not match
- How long the number is good, and that extras need a written OK
If the attic coil is unknown, say so. 'Price assumes the indoor coil matches. If it does not, we stop and send a new number.' That sentence saves the Friday fight. The same idea as a construction change order: extra work needs a price before you start — not after the old evaporator is in the truck.
Walk the job before you send the number
Photos of the pad, the disconnect, the attic hatch, the flue on a UK boiler, the meter, the neighbor's tree that kills the crane swing. Measure the line set. Read the breaker. Ask where the condensate currently goes. A quote written from a phone photo of the outdoor unit is how you miss a 50-foot line set in a two-storey with no chase.
Put those photos on the project the same day. When the customer asks two weeks later 'why did it go up', you have the hatch photo, not a memory. Job notes from the walk belong with the number: write the changeout notes before you leave.
When the customer changes the unit after you quoted
They saw a higher SEER online. They want heat pump instead of straight cool. They want the furnace swapped 'while you are there'. That is a new number. Write what changed, the new price, and that work does not start until they confirm in a message. Do not 'get going' on the original quote while the equipment in the van is the other one.
Where the quote should live
Not only in email. Not only in the estimating app. On the project, next to the schedule and the receipts. When the supply house invoice arrives, you check it against the quoted equipment, not against a thread named 'Re: Re: unit'. Receipts and job cost are the other half of the same number.
Maintenance agreements need a number too: what each visit includes, what a repair during the visit costs, and whether filters are in. Dumping that into WhatsApp is how a customer thought 'tune-up' meant a new capacitor every time. Keep the agreement on the maintenance project: maintenance visit log.
Scheduling the work you just sold
A quote without a date is a maybe. Once they accept, the changeout needs stages on the plan — recovery, set, start-up — not 'sometime next week'. That is HVAC scheduling for small contractors. If you sell six changeouts into the same Thursday, the quotes were fine and the week is not.
A number that survives the first hour on site
Most HVAC quotes die in the first hour, not in the office. You priced a pad swap. The pad is cracked and half an inch out of level. You priced a straight cool. The customer wants a heat pump because the neighbour just got one. You priced a 25-foot line set. The chase is blocked and the run is 42. If the quote said 'site as seen on Tuesday', you can stop and send a new number. If the quote said nothing about the pad, you are negotiating with a unit already on the truck.
Write three site assumptions in every changeout number: access (hatch size, crane swing, parking), indoor match (coil, furnace, or air handler as seen — or 'not seen'), and electrical as seen. When an assumption fails, the extra is not a surprise. It is the sentence you already wrote. UK quotations for a boiler swap should do the same for flue route, condensate, and gas tightness. Australian air-con quotes should say whether a wall chase is included. Canadian HVAC estimates should say if a permit is in or out. The market word changes. The assumption list does not.
Keep the sold PDF next to those assumptions on the project. When the helper asks 'are we doing the thermostat', the answer is on the page, not in a call you had in the driveway. That is the whole point of putting the quote on the job instead of leaving it in email.
Free vs paid — Basic: first month free, then $25/month
Helmate is an app. Basic: first month free, then $25/month for one open project (planning or active). Finished jobs do not count. Calendar and tasks on that project are included. Hands-free talk, receipt scan, work email, and WhatsApp from the business are not on Basic.
Paid plans, from the catalog: Pro Site — $50 up to 3 open projects, hands-free talk and receipt scan, email and 1:1 WhatsApp, ₪5 of assistant help per day, 10GB storage. Pro Crew — $75 up to 10 open projects, export numbers for the office, ₪8 of assistant help per day, 15GB, everything in Pro Site. Pro Command — $125 unlimited open projects, WhatsApp groups, priority support, ₪12 of assistant help per day, 20GB, everything in Pro Crew.
You do not need a paid plan to keep one quoted changeout as a project with the PDF and the photos. Pay when you have several open installs at once, or when you want receipt scan and voice on site. Helmate is an app for that project file, not a replacement for your quoting spreadsheet if that spreadsheet already works.
Honest limits
Helmate does not send the customer a branded estimate with e-sign. It does not take the payment. It does not invent a price. Those are field-service features other vendors sell. We do not copy their price list onto this page. We keep the job behind the number: scope, notes, photos, receipts, dates.
FAQ
Is an HVAC quote the same as an estimate?
In the US many shops use both words for the same document. 'Quote' often sounds firmer. 'Estimate' sounds like it can move. Write the scope so the word does not matter: what is in, what is out, and that extras need a written OK. In the UK send a quotation. In Australia, quote the air-con install in the language the customer used.
Does Helmate create HVAC quotes?
No. Helmate is an app for the project: notes, budget, receipts, photos, calendar. You write the quote in the tool you already use, then keep it on the job so the number sits next to the work. We do not invent a quote builder.
What must be on a changeout quote?
Old and new equipment, refrigerant recovery, line set and electrical, crane and permit if they apply, indoor coil assumptions, exclusions, how long the number is good, and that extras need approval before work starts.
When should you redo the number?
When the model changes, when the attic coil does not match, when they add a furnace or a thermostat package, or when access is not what you priced. Send the new number and wait for a written OK. Do not start on the old page.
When do you pay for an HVAC app beyond Basic?
Basic: first month free, then $25/month for one open project with calendar and tasks. Choose Pro when you need more open jobs, or voice, receipt scan, email, and WhatsApp. Pro Site is $50 (3 projects), Pro Crew $75 (10), Pro Command $125 (unlimited open projects).
